Winter pool covers are important for general maintenance and properly closing a pool at the end of the season. Winter pool covers help prevent leaves, dirt, and debris from falling into the pool during the winter, leading to far less clean up and an easier start-up in the spring. The Blue Wave® Arctic Armor™ pool cover line, manufactured by Blue Wave Pool Products, offers a complete variety of in-ground and above-ground pool covers and winter accessories to suit every pool owner's needs. Here are some highlights about the many great reasons to invest in the best winter pool cover you can buy:
LONG-LASTING WOVEN MATERIAL MAKES THESE POOL COVERS STRONGER
Arctic Armor pool covers are woven from strong, long-lasting polyethylene tapes to hold up against to winter's worst punishment.
REDUCE ALGAE GROWTH IN YOUR POOL WATER
The extremely strong and tight woven fabric that makes up an Arctic Armor pool cover will not allow light to pass through it. And without sunlight, algae growth is stopped in its tracks!
BIGGER OVERLAP LEADS TO LONGER WEAR ON ABOVE-GROUND POOL COVERS
Blue Wave’s manufacturing process does not limit the woven fabric. Each Arctic Armor above ground pool cover has an extra foot of material—making it the largest overlap in the industry and a super value! More material less money. A 4-ft. overlap enables a better fit, especially on above ground pools with extra wide top-rails. This extra fabric also takes up some of the slack during windy weather, preventing excessive wear and tear like inferior, smaller, 3-foot overlap pool covers. Better still, the arctic armor pool covers are held secure with a heavy-duty vinyl-coated cable and fastener anchored by rip-proof metal grommets.
ENJOY WELL-FASTENED SECURITY WITH ALL IN GROUND POOL COVERS
Blue Wave Arctic Armor in ground pool covers are equipped with loops every four feet to secure water bags and corner grommets, which allow for extra tie-down in windy areas. The pool cover is manufactured five feet longer and wider than the pool size.
All Blue Wave Arctic Armor in ground pool covers are super strong and built to last. Protect your in ground or above ground pool and extend your hard-earned money. Make a smart purchase and buy a Blue Wave Arctic Armor pool cover that will go the distance pool season after pool season.
WHY USE ARCTIC ARMOR WINTER POOL COVERS?
Winter pool covers are an important part of the swimming pool winterizing maintenance process. Pool covers keep swimming pools clear of leaves and other unwanted debris. Some winter pool covers are made of mesh to allow rain water to pass through the cover. Winter pool covers also reduce the risk of frost damage to your pool.
From a security standpoint, good-quality pool covers truly add up by helping prevent pets, and other small animals from falling into the pool when they attempt to walk on the pool cover or drink the accumulated water.
Almost any above ground or in ground pool—no matter its shape or size—can be fit with a pool cover, including shaping for steps and ladder entry points. All Arctic Armor winter pool covers are made from UV-stabilized polyethylene fabric for strength and security, and stitched with anti-rot thread. Normally these pool covers feature anti-abrasion strips and PVC reinforcement affixed at potentially high-wear areas.
|
Quick Tip:
The scrim or strands are the weave tightness in the underlying thread construction of the pool cover. The higher the scrim number, the better the quality of the winter pool cover. In areas that reach freezing temperatures, it is important to close a pool properly. This varies greatly between in-ground and above-ground pools. By taking steps to properly secure the pool, it lessens the likelihood that the superstructure will be damaged or compromised by freezing water.
|
TYPES OF ARCTIC ARMOR™ WINTER POOL COVERS:
Solid Winter Pool Covers:
Rugged polyethylene scrim and coating means this pool cover can withstand winter’s worst weather. Arctic Armor pool covers are manufactured with U.V. protected material so they will last for years in direct sunlight. The pool cover’s black underside retards algae growth and heat sealed seams means a crystal clear pool next spring. The big 4 foot overlap on above ground pool covers and 5 foot overlap on in ground pool covers ensures a proper fit and helps the winter cover from stretching and ripping like inferior pool covers with smaller overlaps. Pool covers also provide some added safety for preventing unwanted pool entry, but should not be relied on for that purpose. Arctic Armor Winter Pool Covers are available for Above Ground and In Ground pools, in Bronze, Silver and Gold quality levels. They are backed by 8-Year (bronze), 12-Year (silver) or 15-Year (gold) Warranties.
Mesh Winter Pool Covers:
Arctic Armor Rugged Mesh pool covers make spring clean-up a snap. The secret to this unique pool cover is the tightly woven polyethylene scrim material that holds together to help prevent gaps or holes developing in the cover. Rugged mesh cover material allows only rain water and very fine silt to pass through. Since this rugged pool cover is made of mesh that is very lightweight, simply lift it off in the spring. No heavy water to drain off or time consuming water pumping. Simply remove the rugged mesh pool cover and vacuum up the fine silt and open your swimming pool. In addition, the rugged mesh pool cover’s fine mesh allows rain and snow to slowly fill your pool, saving water and pool chemicals in the spring. Since the scrim cover material is so tightly woven, the pool cover allows almost no sunlight to pass through and helps eliminate algae-free swimming pool in the spring. Arctic Armor's rugged mesh pool covers are made from tough U.V. protected woven polyethylene that is strong enough to handle ice, snow, sleet and high winds. Rugged double stitched hems are triple reinforced for strength and the winter pool cover's black underside retards algae growth. Available for Above Ground and In Ground swimming pools, Arctic Armor Rugged Mesh Pool Covers are backed by an 8-Year Manufacturer Warranty!
Pool Leaf Nets:
Lightweight pool covers made of an open weave material that fits on top of a winter pool cover or solar pool cover to prevent accumulation of wet, heavy, saturated leaves and twigs on top of the cover. These nets ensure faster removal of leaves, and prolong the life of a winter or solar cover. They can be used in any season, and are a big plus if a pool is located in an area surrounded by trees. The open weave design allows water to pass through the net, but will block twigs, leaves and trash. Leaf nets facilitate the removal of a pool cover every time. Arctic Armor Leaf Nets are available for Above-Ground and In-Ground pools and are backed by a 4-Year Warranty.
Safety Pool Covers:
Security for an in ground pool has never been more important. Safety pool covers are one of the most important pieces of pool equipment for establishing safe conditions and peace of mind—especially for pool owners with children in their homes, visiting or in the neighborhood. Available in mesh or a solid vinyl material, these safety covers function as a maintenance tool as well as a safety barrier. All safety pool covers must meet the requirements in the ASTM standards F1346-91 (1996)—meaning the cover must be able to support the weight of a small child or animal that may walk onto the cover. A proper safety pool cover is securely anchored into the pool deck and lies flush so there are no gaps between the pool and the safety cover. A good safety pool cover will provide peace of mind only if it is made from material that will not tear, so that a hole will not increase in size and instead can be patched. Safety pool covers follow the shape of the pool with the proper number of pool deck anchors embedded around the swimming pool to hold the safety cover in place.
MORE POOL COVER BASICS
For an in-ground pool, a solid winter pool cover is held in place by water bags that are placed around the edge inside sleeves attached to the pool cover.
An above-ground pool uses the same type of solid winter pool cover, but instead it is held by a combination winch and vinyl-coated cable assembly that runs through grommets in the outside edge of the pool cover.
Inflatable air pillows rest on the water under the pool cover to allow the rain or melting water runoff of the winter cover.
Many winter covers are designed to block sunlight, which helps prevents algae growth in the pool water. Algae growth prevention is an important part of winterizing the pool. Winter covers actually lead to clearer easier to care for pool water and less expensive pool start-up processes in the spring.
Remember:
- A covered swimming pool will see less freezing than an uncovered swimming pool.
- The properly fitting safety pool cover will help protect children, adults and animals from falling into the pool water.
- A winter pool cover will prevent leaves, dirt, and debris from entering a pool during harsh winter weather, resulting in less messy cleanup in the spring—and less stress.
Pool Winterizing 1-2-3
In climates where there is no risk of freezing, closing down the pool for winter while important is not so vital. But in preparation for freezing temperatures, the pipes of an in-ground swimming pool must be emptied. An above-ground pool also needs to be winterized and closed so that ice forming in and around the pool does not drag down the pool wall, collapsing its structure.
Swimming pool plumbing should be sealed with air—typically with rubber plugs—to prevent cracking from freezing water. The pool should be covered to prevent leaves and other debris from falling in. The winter pool cover is attached to the pool via a cable and winch and or a stretch cord and hooks fitted into the pool surround.
The pool skimmer should be closed off and sealed or a floating device is placed in the skimmer to prevent it from completely freezing and cracking. Floating objects such as life rings or basketballs should be removed or and can be placed in the pool to prevent freezing under the winter cover. Drain plugs on the pool filter should be removed after the filter has been cleaned and winter pool chemicals should be added to keep the pool water clean and easier to prepare the following spring.
Browse these step-by-step guides for the complete process of winterizing a pool.
How to winterize an above-ground swimming pool
Step 1
Prior to closing the pool; ensure that the water is chemically balanced. Adjust chemical levels if necessary. This is a very important step because chemically balanced water protects the pool from corrosion or scale buildup that can occur when the pool is shut down. Chemical levels should read as follows:
- pH 7.2 - 7.6
- Alkalinity 80 - 120 parts per million
- Calcium Hardness 175 - 250 parts per million
- Chlorine 1 - 3 parts per million
Quick Tip:
Use Blue Wave® Winterizing Pool Chemical Kits!
Comes with all the pool chemicals you need to winterize your pool, including FREE pool closing instructions!
Step 2
Remove all pool deck equipment (pool ladders, pool rails, etc.)
Step 3
Brush down the sides and pool floor then vacuum. This is important because if any debris or dirt is left in the pool, staining can occur on the pool liner.
Step 4
Add Blue Wave winterizing pool chemicals by broadcasting them into the deep end of the pool to help protect water quality during the winter/off-season.
Step 5
Clean the pool filter, skimmer, and pump basket. Remove all unused chlorine product from the chlorinator. Cartridge filter elements and D.E. grids should be cleaned and stored. If a sand pool filter is used, it should be backwashed.
Step 6
A skimmer guard can be inserted in the pool skimmer and the return line plugged, or the pool water level can be lowered below the returns—where the water jets into the pool—and the skimmer. Either method is strictly user preference and suitable for pool closing time.
|
Quick Tip:
NEVER COMPLETELY DRAIN A POOL! This may cause the pool to collapse.
|
Step 7
All detachable, flexible hoses, these should be removed and stored. Also remove all drain plugs from the pool pump, filter tank, and any other pool equipment. Follow the manufacturer’s instructions for specific equipment. Place all drain plugs in the pump basket for storage.
If the pool is hard plumbed, use an air compressor or Shop Vac (attached to the blower side of the vacuum) to blow water out of the piping system by forcing air down the skimmer and through the pool plumbing.
Step 8
If using an air pillow, inflate by Shop Vac. Tie the air pillow at two places and position it in the center of the above ground pool. Tie strings to the pool wall so the pillow will not move during cover installation. Air pillows are commonly used, but not absolutely necessary. They are a good idea in colder climates in case the water freezes and expands. The water will freeze inward on the pillow instead of outward, which may damage the pool wall. Air pillows are NOT used to create a dome-like effect to keep rain off of the cover. This will not work. Instead, the rain water will simply settle around the pillow.
Step 9
Position a winter pool cover over the pool surface, black side down.
- Winter Pool Cover installation process, above-ground pools:
Place the cover over the pool, and then thread the cable through loops or grommets. Use the winch provided with the cover to tighten the cable.
- Winter Pool Cover installation process, above-ground pools with decks:
Place water tubes end to end around the edge of the pool. Fill the water tubes 3/4 full of water. DO NOT OVERFILL because water expands when freezing and it could burst the water tubes. Never use bricks, concrete blocks, or other objects to secure the winter cover since they can damage both the pool cover and the pool or pool deck.
Step 10
Some winter covers may require placing a cover pump in the center of the pool cover to drain off excess water. This is very important because too much water on top of the winter cover can cause the cover to rip or pull the cover and water tubes into the pool. This will result in a very messy cleanup.
How to winterize an in-ground swimming pool
Step 1
Prior to closing an in ground pool, ensure that the pool water is chemically balanced. Adjust pool chemical levels if necessary. This is a very important step because chemically balanced pool water protects the pool and pool equipment from corrosion or scale buildup that can occur when the pool is closed. Pool chemical levels should read as follows:
- pH 7.2 - 7.6
- Alkalinity 80 - 120 parts per million
- Calcium Hardness 175 - 250 parts per million
- Chlorine 1 - 3 parts per million
Quick Tip:
Use Blue Wave® Winterizing Pool Chemical Kits to get your pool winter-ready!
Comes with all the chemicals you need to winterize your pool, including FREE pool closing instructions!
Step 2
Remove all pool deck equipment (pool ladders, rails, etc.)
Step 3
Brush down the sides and pool floor and then vacuum. This is important because if any debris or dirt is left in the pool, staining can occur.
Step 4
Add Blue Wave winterizing pool chemicals by broadcasting them into the deep end of the pool to help protect water quality during the off-season.
Step 5
Clean the filter, skimmer, and pump basket. Remove all unused chlorine product from the chlorinator. Cartridge filter elements and D.E. grids should be cleaned and stored. If a sand filter is used, it should be backwashed.
Step 6
Lower the water in the pool below the returns—where the water jets into the pool—and the skimmer. Use an air compressor or Shop Vac attached to the blower side of the vacuum to blow water out of the system by forcing air down the skimmer and through the plumbing.
|
Quick Tip:
NEVER COMPLETELY DRAIN A POOL! This may cause the pool to collapse.
|
Step 7
Cap off pool return lines by using threaded plugs, or use expandable rubber plugs if the returns are not threaded. Add pool antifreeze by pouring it through the skimmer. Use one gallon of antifreeze per 10 feet of distance from the pump to the pool.
Step 8
Remove all drain plugs from the pool pump, filter tank, and any other pool equipment. Follow the manufacturer's instructions for specific equipment. Place all drain plugs in the pump basket for storage.
Step 9
Install a winter pool cover over the pool surface, black side down.
Cover installation process, in-ground pools: Place water tubes end to end around the edge of the pool. Fill water tubes 3/4 full of water. DO NOT OVERFILL since water expands when freezing and it could burst the water tubes. Never use concrete blocks, bricks, or other objects to secure the cover because they can damage both the pool cover and the pool.
Step 10
Place a cover pump in the center of the pool cover to drain off excess water accumulation. This is very important because too much water on top of the cover can cause the cover to rip or pull the cover and water tubes into the pool. This will result in a very messy cleanup.
SOLID WINTER POOL COVER INSTALLATION
IN-GROUND WINTER POOL COVER INSTALLATION
1. If you find that your pool cover is too small, do not stretch it across the pool in an attempt to make it fit. Your pool cover should fit your pool as shown in the diagram below.
2. Your pool cover is made to have rainwater accumulate on top of it all winter. This water will not damage your pool cover in any way. Do not pump off the cover during the Fall. Water on top of the cover will hold it in place and protect your winter pool cover from wind damage.
3. Your winter cover is sized for a maximum water drop below the deck of 18". If you normally drop your water more than 18" in the Fall, return your pool cover for a larger size. Refer to Diagram 1 for proper fit.
4. Do not use bricks or sharp blocks to weigh down your pool cover as they will cut, scuff and damage the pool cover. We recommend using water tubes to secure the winter pool cover.
5. If you tie your winter pool cover to a fence or other permanent structure, be sure to use a flexible bungee cord. This flexible cord will allow the pool cover to shift as snow and ice accumulates without pulling out the corner tabs or straps. Water tubes must still be used to secure the winter pool cover.
ABOVE-GROUND SOLID WINTER POOL COVER INSTALLATION
1. Place winter pool cover over the entire pool and let it rest on the pool water.
2. Your winter cover is made to have rainwater accumulate on top. This water will not damage your winter pool cover in any way. Do not pump off the pool cover during the Fall. Water on top of the winter cover will hold it in place and protect the winter cover from wind damage.
3. Your winter pool cover is sized for maximum water drop below the deck of about 12". If you drop your water more than 12", order a larger size.
4. Your winter pool cover should hug the sidewall of your pool and lay on top of the pool water. Stretching the winter cover will damage it. See image below for Correct and Incorrect installation diagrams.
5. Thread cable through the cover loops and use the ratchet to tighten it.
MESH WINTER POOL COVER INSTALLATION
IN-GROUND MESH WINTER POOL COVER INSTALLATION
1. If you find that your cover is too small, do not stretch it across the pool in an attempt to make it fit. Your cover should fit your pool as shown in the diagram below.
2. Your winter cover is made to have rainwater accumulate on top of it all winter. The water will slowly drain through the mesh winter pool cover. This water will not damage your cover in any way. Do not pump off the cover during the Fall. Water on top of the cover will hold it in place and protect your winter cover from wind damage.
3. Your winter pool cover is sized for a maximum water drop below the deck of 18". If you normally drop your pool water more than 18" in the Fall, return your winter cover for a larger size. Refer to Diagram 1 for proper fit.
4. Do not use bricks or sharp blocks to weigh down your cover as they will cut, scuff and damage the winter cover. We recommend using water tubes to secure the winter pool cover.
5. If you tie your winter cover to a fence or other permanent structure, be sure to use a flexible bungee cord. This flexible cord will allow the winter pool cover to shift as snow and ice accumulates without pulling out the corner tabs or straps. Water tubes must still be used.
ABOVE-GROUND MESH WINTER POOL COVER INSTALLATION
1. Place pool cover over the entire pool and let it rest on the water.
2. Your winter cover is made to have rainwater accumulate on top of it all winter. The water will slowly drain through the mesh cover. This water will not damage your cover in any way. Do not pump off the winter cover during the Fall. Water on top of the cover will hold it in place and protect your pool cover from wind damage.
3. Your pool cover is sized for maximum water drop below the deck of about 12". If you drop your water more than 12", order a larger size.
4. Your winter pool cover should hug the sidewall of your pool and lay on top of the water. Stretching the winter cover will damage it. See image below for Correct and Incorrect installation diagrams.
5. Thread cable through the cover loops and use the ratchet to tighten it.
LEAF NET INSTALLATION
IN-GROUND POOL LEAF NET INSTALLATION
1. INSTALL YOUR LEAF NET ON TOP OF YOUR WINTER POOL COVER.
2. If you find that your leaf net is too small, do not stretch it across the pool in an attempt to make it fit. Your leaf net should fit on top of your winter pool cover.
3. Do not use bricks or sharp blocks to weigh down your leaf net as they will cut and scuff the leaf net pool cover. We recommend using water tubes for leaf net installation.
5. If you tie your leaf net to a fence or other permanent structure, be sure to use a flexible bungee cord. This flexible cord will allow the leaf net to shift as snow and ice accumulates without pulling out the corner tabs or straps. Water tubes must still be used.
ABOVE-GROUND POOL LEAF NET INSTALLATION
1. INSTALL YOUR LEAF NET ON TOP OF YOUR WINTER COVER.
2. Place leaf net over the entire pool and let it rest on the winter pool cover.
3. Your leaf net should hug the sidewall of your pool and lay on top of the winter pool cover. Stretching the leaf net will damage it.
ARCTIC ARMOR SOLID WINTER POOL COVERS
ABOVE-GROUND ARCTIC ARMOR BRONZE WINTER POOL COVERS
 Blue Wave Arctic Armor Bronze is a high-quality; entry-level above-ground winter pool covers with the strength and durability of winter covers costing twice as much. Rugged polyethylene scrim and coating stand up to winter's worst punishment. And all Blue Wave Arctic Armor winter pool covers are UV-protected to last for years in direct sunlight. Arctic Armor Bronze winter pool covers are navy blue with a black underside and heat-sealed seams that prevent algae growth. Its larger 4-foot overlap ensures a proper fit to keep the winter cover from stretching and ripping—a problem often seen with pool covers with only a 3-foot overlap.
Arctic Armor Bronze winter pool covers are held secure on the above ground pool with a heavy-duty vinyl-coated cable and fastener, anchored by rip-proof metal grommets. This winter cover is backed by an 8-year warranty Manufacturer (1 year fully rated). Available in sizes 12' to 36' Round and 12'x17' to 21'x43' Oval.
|
ABOVE-GROUND ARCTIC ARMOR SILVER WINTER POOL COVER:
 Arctic Armor Silver winter pool cover is a mid-priced pool cover with the strength and durability to ensure years of winter protection. Heavier woven polyethylene strands and coating hold up against wind, sleet, and snow. Arctic Armor Silver winter pool covers are forest green with a black underside and heat-sealed seams to prevent algae growth. All Arctic Armor coves are UV-stabilized for protection from harmful effects of the sun. A larger 4-foot overlap prevents stretching and ripping often found in winter covers with only a 3-foot overlap.
Arctic Armor Silver winter pool covers are held secure on the above ground pool by a heavy-duty vinyl-coated cable and fastener anchored by rip-proof metal grommets. This winter cover is backed by a 12-year warranty Manufacturer (2 years fully rated). Available in sizes 12' to 33' Round and 12'x20' to 21'x41' Oval.
|
ABOVE-GROUND ARCTIC ARMOR GOLD WINTER POOL COVER:
Blue Wave's very best winter pool cover, built to last!
 This fall, invest in the finest-quality winter pool cover available: Arctic Armor Gold. Arctic Armor Gold winter pool covers are made from U.V. stabilized woven polyethylene scrim that protects the winter pool cover from sun, snow, wind and ice. The highly tear- resistant material, with black underside and heat-sealed seams, prevents algae growth for clear pool water come springtime. Arctic Armor Gold has a 4-foot overlap to allow coverage over above ground pools with wider top rails. It will not stretch and rip like winter covers with a shorter 3-foot overlap.
Arctic Armor Gold is held secure by a heavy-duty vinyl-coated cable and fastener, anchored to the cover by rip-proof metal grommets.
Invest in the best: Blue Wave Arctic Armor Gold, winter pool cover backed by a 15-year Manufacturer warranty (3 years fully rated). Available in pool cover sizes 12' to 33' Round and 12'x20' to 21'x41' Oval.
|
|
IN-GROUND ARCTIC ARMOR BRONZE WINTER POOL COVER:
Blue Wave Arctic Armor Bronze in ground winter pool covers are a high-quality, entry-level in-ground winter cover with the strength and durability of pool covers costing twice as much. Rugged polyethylene strands and coating allow Arctic Armor Bronze to withstand winter's worst punishment.
Arctic Armor winter pool covers are U.V. protected to last for years in direct sunlight. A black underside and heat-sealed seams work to retard algae growth for clear swimming pool next spring. Arctic Armor Bronze winter cover comes with loops every four feet to secure water bags. Corner grommets allow for extra tie-down in windy areas.
Measuring 5 feet longer and wider than the in ground pool size, this winter cover is backed by an 8-year Manufacturer warranty. Available in rectangular pool cover sizes from 12'x20' to 30'x60'. |
IN-GROUND ARCTIC ARMOR SILVER WINTER POOL COVER:
Arctic Armor Silver is Blue Wave's mid-priced winter pool cover. Silver status gives this winter cover all the strength and durability required to ensure years of winter pool protection. Heavier woven polyethylene strands and coating readily withstand wind, sleet, and snow. The in ground winter pool cover is U.V. stabilized to protect it from the harmful effects of the sun.
Arctic Armor Silver winter pool covers have a black underside and heat-sealed seams to retard algae growth. The pool cover has loops positioned every four feet to secure water bags. Corner grommets allow for extra tie-down in windy areas.
Measuring 5 feet longer and wider than the in ground pool size, Arctic Armor Silver pool covers are backed by a 12-year Manufacturer warranty (2 years fully rated). Available in pool cover rectangular sizes from 12'x20' to 30'x60'. |
IN-GROUND ARCTIC ARMOR GOLD WINTER POOL COVER:
This in-ground winter pool cover is built to last!
Constructed of our strongest and most tear resistant material, Arctic Armor Gold winter pool covers boast a UV-stabilized woven polyethylene strand that protects the cover from sun, snow, wind, and ice.
The black underside and heat-sealed seam retard algae growth to help ensure clear pool water in the springtime.
Our Gold cover comes with loops every four feet to secure water bags and corner grommets to allow for extra tie down in windy areas. The cover is 5 feet longer and wider than the pool size and is backed by a 15 year Manufacturer warranty (3 years full rated). Invest in the best this fall with Arctic Armor Gold winter pool cover. Available in rectangular in ground winter pool cover sizes from 12'x20' to 30'x60'. |
|
|
ARCTIC ARMOR™ MESH WINTER POOL COVERS
|
|
Environmentally friendly design leads to quick springtime cleanup- backed by an 8-year Manufacturer warranty.
 Blue Wave Arctic Armor rugged mesh winter pool covers feature tightly woven scrim that holds together to ensure no gaps or holes develop. The rugged mesh design allows only rain water and very fine silt to pass through, slowly filling the pool—and saving water and chemicals costs in the spring.
The rugged mesh design allows virtually no sunlight to pass through, stopping algae in its tracks. Better yet, with this lightweight mesh, simply lift the cover off in the spring. No heavy water to deal with; no time-consuming cover pumping. Simply remove the mesh and vacuum up the fine silt. |
|
In-Ground Rugged Mesh Winter Pool Covers
Arctic Armor Rugged Mesh winter pool covers have a 5-foot overlap with loops every four feet to secure water bags. Corner grommets enable extra tie-down in windy areas. Available in rectangular pool cover sizes from 12'x20' to 30'x60'.
Above-Ground Rugged Mesh Winter Pool Covers
Above Ground Arctic Armor rugged mesh winter pool covers have a 4-foot overlap, and include a cable and winch fastener. Available in 12' to 33' Round and 12'x20' to 21'x41' Oval pool cover sizes.
|
|
|
ARCTIC ARMOR™ LEAF NET POOL COVERS
|
|
ELIMINATE THE MESS CAUSED BY DECAYING LEAVES EACH SPRING!
 Install an Arctic Armor above ground or in ground pool leaf net over your winter pool cover this fall and make spring opening quick and easy. The leaf net’s tight mesh traps even the smallest leaves before they reach your winter cover. Other brands of leaf nets have larger mesh that allows small leaves to pass through to your winter pool cover and decompose in the spring. Simply lay leaf net on top of your winter pool cover when you close your pool and remove it in November before the first snow. Your cover will be virtually leaf free and spring clean-up will be a snap. Eliminates that messy swamp of decaying leaves!
Arctic Armor pool leaf nets are made from durable woven polyethylene and carry a 4 year Manufacturer warranty. If you live in an area where leaves are a problem invest in a quality Arctic Armor pool leaf net cover.
|
|
IN-GROUND POOL LEAF NETS
In-ground leaf nets have an extra 4-foot overlap and water tube loops for a secure fit over your in ground winter pool cover. Black mesh fabric. Available in rectangular sizes from 12'x20' to 30'x60'.
ABOVE-GROUND POOL LEAF NETS
Above-ground leaf nets have an extra 3-foot overlap and include a cable and winch to hold it securely in place over your winter pool cover. Black mesh fabric. Available in 12' to 33' Round and 12'x20' to 21'x41' Oval sizes.
|